Knowledge & Insights

Insights into UZIN UTZ Industry’s bonding technologies

UZIN UTZ Industry has expertise in a range of bonding technologies. We select each technology to suit the complete system and the process involved. This overview introduces our technologies, which can also be developed, adapted and tested for your specific application.

Our bonding technologies at a glance

Technology Particularly suitable for Key process benefit
Dry adhesives Floor, wall and stair coverings Immediate loading and reversible bonding
Adhesive tape technologies Profiles, skirting boards and components Precise bonding and easy assembly
Wet adhesives Permanent bonds under high loads High strength and resistance
Dispersion-based primers Substrate preparation and system changes Reproducible adhesion
Combined systems Hybrid assemblies designed for the lifecycle Permanent bonds with selective removal
Coating systems Surfaces, panels and functional modules Protection and long-term surface performance

Self-adhesive solutions and dry adhesives

0 minutes waiting time, 100% process speed

Dry adhesives create fast, clean bonds without flash-off or curing times. Self-adhesive solutions can be loaded immediately after installation, whether supplied as dry adhesive, tape or on a roll. Depending on the system, they can also be removed without residue when required.

Easy handling reduces the need for specialist tools and extensive application expertise. This is a clear advantage for high production rates and steady operations. Self-adhesive solutions are therefore particularly suitable for fast processes and straightforward dismantling.

Typical applications

Dry adhesives are often used in prefabricated flooring systems, vehicles and modules. Typical applications include:

  • Floor coverings
  • Wall coverings and panels
  • Stairs and steps
  • Skirting boards and profiles
  • Modular components

FAQs about self-adhesive solutions and dry adhesives

Dry adhesives can be integrated directly into industrial series production as part of the bonding process. The self-adhesive layer can be applied to floor coverings, profiles, panels or other components at the factory. During subsequent assembly, the release liner is removed, and the component is positioned and pressed into place. With no flash-off, drying or curing time, the next steps can begin immediately.

For manufacturers, integrating dry adhesives means shorter lead times, higher production rates and more predictable workflows. It also eliminates mixing, dispensing and cleaning steps that may be required with liquid adhesives. Self-adhesive solutions for surface bonding are particularly suitable for industrial prefabrication, modular construction, and the manufacture and maintenance of vehicle, flooring and interior systems. Each solution is designed around the materials, component geometry, production cycle and future loads.

Yes. Components can be fitted with a tailored self-adhesive layer during industrial manufacturing, then stored, transported and assembled at their intended location. The self-adhesive solution is applied to the component or material at the factory and protected by a release liner until assembly.

Pre-application is suitable for floor coverings, skirting boards, profiles, linings, vehicle parts and prefabricated modules, for example. It moves steps from the construction site or final assembly into a controlled production environment, allowing consistent application quality, accurate positioning and controlled dimensions. On site or during final assembly, the process is reduced to positioning, pressing into place and any necessary finishing work.

Before release for series production, the self-adhesive system, carrier material, release liner and intended storage, transport and assembly conditions must be tested together. UZIN UTZ Industry offers tailored self-adhesive preparation and application-specific system testing for this purpose.

For repeatable results, the dry adhesive, component, substrate and application process must be considered as one bonding system. Key process parameters include the material combination, condition and cleanliness of the bonding surfaces, accurate positioning, uniform application and defined pressing conditions.

Conditions during manufacturing, storage, transport and subsequent use must also be considered. These include temperature ranges, mechanical loads, dimensional changes in the bonded materials and ageing effects. For components with pre-applied self-adhesive layers, lamination quality, the release liner and storage stability must also be checked.

Specific limits can only be defined for the individual industrial application. New materials and system assemblies are therefore tested for bond performance, compatibility, dimensional stability and ageing resistance before release for series production. A documented process specification then provides the basis for consistent production quality and quality assurance.

Suitable self-adhesive solutions can be designed for high static and dynamic loads and changing temperatures. However, the complete system must be tested, including the substrate, dry adhesive, component or covering, and intended service conditions.

In vehicles, modular systems and areas used for industrial purposes, bonds are often exposed to vibration, rolling loads, heavy traffic, temperature changes and dimensional changes in the materials. Assessing initial adhesion alone is therefore insufficient. Approval also requires testing of long-term behaviour, temperature and ageing resistance, and compatibility between the bonded materials.

UZIN UTZ dry adhesive systems are developed for static and dynamic loads and assessed through application-specific testing. However, no single statement applies to every material combination. Suitability for vibration, temperature fluctuations and mechanical loads must be confirmed for each project in the intended system.

Dismantling should be planned when designing the component and selecting the bonding system. To support dismantling for recycling and Design for Disassembly, teams define early which components should remain permanently bonded and which should be removable during repairs, modernisation or at the end of the lifecycle.

Depending on the system, reversible dry adhesives allow coverings or components to be removed without residue or damage to the underlying substrate. Individual components can then be replaced, and materials separated for suitable recycling processes. Reversible bonds also simplify servicing and maintenance because the entire system does not need to be replaced.

During product development, bonding areas must therefore remain accessible, material combinations must be tested for separation, and dismantling processes tested in practice. The intended number of use, modification or replacement cycles should also inform system design. Dismantling becomes an integral part of lifecycle planning, rather than a task considered afterwards.

Adhesive tape technologies

100% fixing, 0% solvent

Double-sided adhesive tapes, thread scrims, adhesive film systems and other tape solutions allow different elements to be bonded precisely and consistently. They are easy to assemble, solvent-free and load-resistant. Depending on the system, they can also be removed when required.

Tapes can be applied to components at the factory and protected with a release liner for storage, transport and later assembly. During final assembly, elements can be positioned, secured and processed further immediately, enabling repeatable workflows, short assembly times and consistently high quality in industrial series production.

Typical applications

Adhesive tape technologies are often used to make parts and components self-adhesive at the factory. Typical applications include:

  • Skirting boards and profiles
  • Flooring and wall strips
  • Panels and linings
  • Edge and transition components
  • Vehicle and module components
  • Prefabricated components for final assembly

FAQs about adhesive tape technologies

The right tape construction depends on the materials to be bonded, component geometry, surface condition and subsequent mechanical and thermal loads. The complete system of adhesive, carrier, component and substrate is always the deciding factor.

Adhesive film systems are particularly suitable for flat, dimensionally accurate surfaces and precise, uniform adhesive transfer. Tapes with thread scrims or textile carriers can provide additional stability. Depending on their construction, they can also suit profiles, linings, curved surfaces and irregular geometries. Foam carriers can compensate for minor unevenness and distribute loads within the bond.

Selecting an industrial adhesive tape solution requires consideration of shear forces, tensile and peel loads, vibration, temperature changes, moisture, ageing and the intended service life. Final approval should therefore be based on material, load and ageing tests on the actual component. UZIN UTZ Industry develops tailored tape and system solutions for each industrial application.

Industrial adhesive tapes can be integrated into manufacturing as rolls, pre-cut pieces or pre-applied self-adhesive layers. Application may be manual, semi-automatic or automatic, depending on component geometry, production volume and cycle time.

In semi-automatic tape application, components can be guided while the tape is unrolled by machine, positioned, pressed into place and cut to length. In automated series production, application can be combined with feeding, positioning and quality control within one production station. Factory pre-application is also possible: tape is applied to floor coverings, profiles, panels or other components and protected with a release liner until final assembly.

Effective process integration requires tape width, application speed, positioning accuracy, pressing conditions and component guidance to be coordinated. Dry adhesive and tape solutions require no flash-off or curing time, so subsequent manufacturing or assembly steps can begin immediately. This supports short lead times, high production rates and repeatable workflows in industrial series production.

There are no universal manufacturing tolerances for industrial adhesive tape bonds. Acceptable values must be defined for each combination of tape, material, component geometry, production process and loads, then validated before release for series production.

For repeatable bonding results, the following parameters are particularly important:

  • Tape position and distance from component edges
  • Width and complete coverage of the intended bonding area
  • Application without wrinkles, bubbles or tension
  • Uniform, defined application pressure
  • Cleanliness, dryness and condition of the surfaces
  • Temperature conditions during application, storage and assembly
  • Dimensional accuracy and tolerances of the bonded components

Insufficient application pressure can prevent full surface wetting. Incorrect positioning or an undersized bonding area can result in unfavourable load transfer. Relevant parameters should therefore be defined as process windows, documented in work or inspection instructions, and confirmed through trials on the actual component. UZIN UTZ Industry considers materials, workflows and standards during development so the adhesive solution can be precisely matched to the manufacturing process.

Yes. Pre-applied tapes can be designed for storage, transport and final assembly at a later date. This requires the tape, carrier material, release liner and logistics conditions to be tested as a complete system.

The release liner protects the bonding surface from dust, dirt and unintended contact until assembly. Industrial approval must consider the intended storage period, temperature and humidity, stacking, packaging, mechanical loads during transport and ease of release liner removal at assembly.

Testing must also establish whether the tape shifts, lifts at the edges or changes properties due to temperature fluctuations and ageing during storage and transport. Long-term testing, material compatibility checks, and tests of dimensional stability and ageing resistance provide the basis for consistent pre-application quality. A component with a self-adhesive layer should only be released for series production after this validation.

Tape bonds can be verified through a combination of process monitoring, visual inspection and application-specific testing. The aim is to check and document key process parameters during application, as well as inspecting the finished component.

During production, records can include tape type, batch, application position, bonding area, surface condition, pressing conditions and time of manufacture. Visual inspection can identify wrinkles, bubbles, contamination, lifting or positioning errors. Depending on safety and quality requirements, additional sampling, adhesion checks, peel or shear tests, and load and ageing tests may be specified.

For comprehensive quality assurance, approved process parameters should be recorded in an inspection plan. Measurements, material batches and deviations can then be documented by component, production run or order. For industrial applications involving safety requirements in particular, tape, material combination, application process and inspection method should be approved together. UZIN UTZ Industry supports manufacturers with material testing, measurement support and application-specific system tests.

Wet adhesives

Permanent bonds, high load resistance

Lasting adhesion, high strength and effective integration into manufacturing: wet adhesives create permanent, stable bonds that withstand demanding loads. Depending on the material, component geometry and requirements, dispersion, contact or reactive adhesives may be used.

They reliably bond floor coverings, wood-based materials, metals, panels and other components, even under high mechanical, thermal and dynamic loads. They can also be applied to a wide range of substrates using different application methods, manually, semi-automatically or fully automatically.

Typical applications

Wet adhesives are mainly used for permanently bonded components exposed to high loads. Typical applications include:

  • Floor coverings in high-traffic areas
  • Panels and sandwich structures
  • Modular and prefabricated components
  • Raised floor systems
  • Bonding metal and wood-based materials
  • Vehicle, ship and rail vehicle manufacturing
  • Skirting boards, profiles and linings
  • Industrial series production and assembly

FAQs about wet adhesives

Wet adhesives can be integrated into industrial manufacturing through defined dispensing, mixing and application steps. The equipment required depends on the adhesive type. Ready-to-use dispersion and contact adhesives require no further mixing, while two-component reactive adhesives must be mixed uniformly in the specified ratio before application.

Depending on viscosity, component geometry and production volume, application may use rollers, trowels, pumps or a method designed for the application. UZIN UTZ offers ready-to-use wet adhesives, including products suitable for roller or pump application. Adhesive application, component feeding and subsequent assembly can therefore be planned as one coordinated process.

Consistent production requires material supply, dispensed quantity, mixing quality, application pattern, component cycle time and cleaning of the application equipment to be coordinated. Specific settings are established during process development using the intended materials and component assembly, then documented in mandatory work and inspection instructions.

Open time, flash-off time and curing time determine when a component can be bonded, processed further, loaded or dispatched. They are therefore among the most important factors influencing cycle time when bonding with wet adhesives in industrial production.

With dispersion and contact adhesives, bonding must take place within the specified working window. After mixing and bonding, reactive adhesives require a defined period to reach the necessary early or final strength. This may require intermediate storage, temporary fixing or additional buffer stations within manufacturing.

For economical series production, the wet adhesive should therefore match the planned line speed, component sequence and required early strength. UZIN UTZ identifies high early strength and load resistance as key application properties of its adhesives. However, specific open, flash-off and curing times vary by product, applied quantity, substrate and ambient conditions. They must be taken from the relevant technical data sheet and approved process specification.

Different substrates can be bonded reliably when the material, surface condition and wet adhesive are tested together during development. Key factors include absorbency, strength, surface texture, existing coatings, moisture and any residues that could impair adhesion.

UZIN UTZ wet adhesives are available for various absorbent and non-absorbent substrates. These include wood and wood-based materials, metals, aluminium foils, steel sheets, gypsum fibre boards and different floor coverings. Suitability always depends on the specific adhesive technology and complete system assembly.

For series production, acceptable substrate quality and ambient conditions should therefore be defined as process windows. Checks may cover cleanliness, moisture, temperature, material batch and surface condition. Where materials vary, preliminary trials, adhesion tests and, where necessary, suitable pretreatment are required. This enables repeatable wet adhesive bonding despite changes in components or production conditions.

A wet adhesive bond is ready for further processing once it has reached the strength required for the next process step and the adhesive application meets the defined quality requirements. Depending on the application, separate approvals may be needed for processing, assembly, transport and final release for series production.

Relevant approval criteria include:

  • Correct adhesive and material batches
  • Complete, uniform wetting of the bonding surface
  • Compliance with the specified mixing ratio and applied quantity
  • Bonding within the specified working window
  • Sufficient early strength for handling and further processing
  • Final strength achieved for use, transport or dispatch
  • Successful adhesion, load and, where required, ageing tests

UZIN UTZ tests new materials and system assemblies for properties including bond performance, resistance, compatibility, dimensional stability and ageing resistance. For industrial series production, these findings should be used to define measurable approval criteria and a documented inspection plan.

Process reliability, health and safety, and bond performance can be combined by selecting the right adhesive technology for the application and developing it as part of the complete manufacturing process. Different chemical systems can meet demanding bonding requirements. Depending on the materials and loads, options include solvent-free dispersion adhesives, water-based contact adhesives and one- or two-component reactive adhesives.

UZIN UTZ offers ready-to-use, solvent-free dispersion adhesives and water-based contact adhesives, for example. High-performance polyurethane and epoxy resin adhesives are available for demanding applications. Selection considers bond performance, substrate, loads and properties relevant to occupational safety.

Safe working conditions also depend on ergonomic application, suitable engineering controls, clear work instructions and user training. UZIN UTZ emphasises solutions with low emissions and low levels of harmful substances, alongside training for high-quality application in production and use. Manufacturers can thereby achieve safe working conditions, repeatable processes and consistently high bond performance together.

Dispersion-based primers

Reinstall up to three times, with no unnecessary dismantling

Dispersion-based primers help reduce extensive substrate preparation and allow coverings to be removed later with almost no residue. Combined with suitable dry adhesive systems, they simplify both initial installation and later reinstallation of coverings, up to three times depending on the system.

This can save time, reduce material use and lower costs, supporting industrial systems designed to be adapted, modified or fitted with new coverings during their lifecycle.

Typical applications

Dispersion-based primers are mainly used in reversible flooring and system assemblies. Typical applications include:

  • Preparation of absorbent and non-absorbent substrates
  • Combination with dry adhesives
  • Changes to flooring and covering systems
  • Refurbishment and reinstallation
  • Modular and reversible assemblies
  • Industrial prefabrication

FAQs about dispersion-based primers

A dispersion-based primer is applied after preparing and cleaning the substrate and before applying the dry adhesive. At this stage, the substrate should be sound, clean, sufficiently dry and free from substances that could impair adhesion.

In industrial series production, primer application should be planned as a defined step between substrate preparation and bonding. After application, the primer must dry under specified conditions before the dry adhesive or self-adhesive system is applied. A defined drying step creates a repeatable surface condition for subsequent bonding, removal and reinstallation.

The ideal point in the process depends on material flow, cycle time and planned intermediate storage. For prefabricated floor, panel or module systems, the primer can be applied at the factory, provided storage stability, protection from contamination and subsequent process steps have been tested as part of the complete system.

The applied quantity and drying conditions have a major influence on whether a dispersion-based primer creates a uniform, repeatable base for subsequent bonding. Too little primer can leave the surface incompletely treated. Too much can extend drying time and produce an uneven layer.

Industrial application therefore requires a defined coat weight or applied quantity, uniform coverage and a mandatory drying window. Relevant factors include the substrate, absorbency, layer thickness, temperature, humidity and air exchange.

The dry adhesive should only be applied once the primer has reached the drying condition specified for the system. Specific limits are tested for each material combination and manufacturing situation, then documented in work and process instructions.

Primer application quality can be checked by monitoring the material, application process and finished layer. During series production, records should cover at least the product batch, applied quantity, application time and drying conditions.

Visual inspection can establish whether the primer forms a uniform, continuous layer without gaps, pooling, contamination or uneven areas. Coat weight, drying condition and adhesion can also be checked through sampling. In automated or semi-automated equipment, application speed, material consumption and process parameters can be monitored as well.

For repeatable quality, a defined inspection plan should specify which characteristics are checked, what tolerances apply and how deviations are handled. UZIN UTZ Industry focuses on the complete system of substrate, primer, adhesive and covering to support consistent quality and release for series production.

A dispersion-based primer can even out differences in absorbency and surface properties, creating a more uniform base for subsequent bonding. This is particularly relevant where industrial production involves different board materials, metals, surfaces treated with smoothing compounds or changing material batches.

However, a primer only improves the properties it is designed to address. Major unevenness, insufficient strength, contamination, moisture or unsuitable surfaces cannot be reliably corrected by primer alone. These issues must be identified and resolved during incoming goods, substrate or process inspections.

For series production, acceptable substrate quality should therefore be defined, and different materials tested in advance for adhesion, compatibility and ease of removal. On this basis, the primer can help reduce variations and maintain repeatable bonding results across batches and components.

 

Dispersion-based primers support reversible industrial systems by making coverings easier to remove and reinstall. Combined with a suitable dry adhesive, the covering can be removed with little effort and almost no residue, preserving the underlying substrate for further use.

Depending on the tested system, reinstallation is possible up to three times. This reduces substrate preparation, material consumption and time during modifications, modernisation or covering replacement. In modular components, vehicles, raised floors and prefabricated flooring systems in particular, it can reduce downtime and lifecycle costs.

Repeated use should be considered during product development. This includes selecting compatible materials, defining dismantling procedures and testing the intended number of replacement cycles. The primer becomes part of lifecycle planning, supporting Design for Disassembly, repairability and dismantling for recycling.

Combined wet and self-adhesive systems

One solution for every stage of the lifecycle

Combined systems bring together the lasting strength of wet adhesives and the speed and reversibility of self-adhesive solutions. This allows individual components within a system to be designed for either permanent or reversible bonding.

Permanent bonding is suitable for connections exposed to high loads. Depending on the system, reversible bonds can be removed without residue during repairs, modernisation or at the end of service life. Combining wet adhesive and self-adhesive systems provides a high degree of flexibility, from long-term, high-load applications to fast, clean dismantling.

Typical applications

Combined wet adhesive and self-adhesive systems are used wherever permanent and reversible bonds need to work together within one system. Typical applications include:

  • Modular structures
  • Prefabricated flooring systems
  • Panels and sandwich structures
  • Components designed for easy repair and maintenance
  • Vehicles and transport equipment
  • Systems with different lifecycles
  • Reversible components within permanently bonded structures

FAQs about combined wet and self-adhesive systems

Permanent bonds should be used for components that carry high static or dynamic loads throughout their intended service life and remain structurally unchanged. These may include load-bearing elements, supporting structures exposed to high loads, or components whose bonds are essential to the stability, safety and durability of the complete system.

Reversible bonds are particularly suitable for wear parts, floor and wall coverings, profiles, covers, or components that will need maintenance, modernisation, replacement or separate recycling during their lifecycle. The choice between wet adhesive and a self-adhesive solution should be made during product development, based on loads, service life, accessibility and planned dismantling.

Combined wet adhesive and self-adhesive systems provide bonds suited to each function: permanent where maximum resistance is required, and reversible where repairability, flexibility and dismantling for recycling take priority.

Wet adhesives and self-adhesive solutions are coordinated according to their function within the industrial system. The design first defines which bonding areas must permanently withstand loads and which components should be removable later. Adhesive technology, substrate, component geometry and intended loads are then assessed together.

In production, application, positioning, drying or curing time and subsequent assembly steps must be coordinated. Self-adhesive solutions allow immediate fixing and further processing, while wet adhesives provide permanent bonds that withstand high loads. This combines fast manufacturing with long-term system stability.

Both bonding technologies need to be considered as part of one complete system assembly. UZIN UTZ Industry coordinates materials, processes and lifecycle requirements to develop solutions that integrate into existing industrial workflows.

Before a combined wet adhesive and self-adhesive system is released for series production, material compatibility, adhesion to the intended substrates and long-term behaviour of the complete assembly must be tested. Testing must establish whether constituents of the wet adhesive, dry adhesive or bonded materials affect the other bond.

Mechanical loads, temperature changes, moisture, ageing and potential dimensional changes in components also matter. Tests must confirm that permanently and reversibly bonded areas carry forces as intended, and that removable components can later be detached without damaging adjacent components or bonding areas.

Release for series production should therefore be based on testing of the actual materials and component assembly. UZIN UTZ Industry can assess new materials and system solutions for properties including bond performance, resistance, compatibility, dimensional stability and ageing resistance.

Combined adhesive systems simplify repairs and modernisation because only the affected components need to be removed and replaced. Permanently bonded supporting structures or load-bearing elements can remain in place, while reversibly fixed coverings, profiles, linings or modules are selectively removed.

This shortens dismantling and assembly times and can reduce substrate preparation. Self-adhesive solutions can be loaded immediately, allowing a rapid return to service. Components removable without residue can also be separated, reused or sent to suitable recycling processes.

In vehicles, modular structures, raised floors and prefabricated flooring systems in particular, this approach enables repair-friendly system design. Downtime, material consumption and work on the complete system can be reduced while the long-term function of permanently bonded areas is maintained.

The additional development work for a combined wet adhesive and self-adhesive system is particularly worthwhile for products and installations with long service lives, regular maintenance intervals or several planned modification and modernisation cycles. Where downtime costs are high, supporting structures are valuable, or legal requirements cover dismantling and recycling, designing around the lifecycle can also offer economic advantages.

The deciding factor is total lifecycle cost. Alongside initial assembly, costs for maintenance, repair, replacement, downtime, substrate preparation and disposal should be considered. Greater investment in development and system testing can pay off when later work is faster, less material needs replacement and individual components can be separated cleanly.

Combined systems are therefore particularly useful when process speed, long-term load resistance and later reversibility are all required. They make planning more predictable across several phases of use and allow manufacturers to design industrial systems for repair, adaptation and dismantling for recycling from the outset.

Coating systems

High surface protection, 0 % VOC

Coating systems create durable, resistant surfaces for industrial applications, protecting them from mechanical, chemical and climatic influences. Multilayer assemblies of primers, fillers, intermediate layers, protective layers and topcoats ensure adhesion and provide high abrasion resistance, scratch resistance and indentation hardness.

UV and LED-UV systems enable fast curing when precisely integrated into industrial manufacturing. VOC-free formulations and LED-UV technologies can contribute to efficient curing and help meet relevant production and regulatory requirements. Manufacturers benefit from consistently high surface quality, repeatable processes and high resistance.

Typical applications

Coating systems are used wherever surfaces need lasting protection, functional finishing or resistance to high loads. Typical applications include:

  • Parquet and floor coverings
  • Panels and modules
  • Functional surfaces
  • Transport and vehicle components
  • Raised floor panels
  • Industrial wood-based materials
  • Surfaces exposed to heavy use
  • UV and LED-UV coating processes

FAQs about coating systems

Industrial coating systems can be integrated into continuous or automated production lines as a defined sequence. Typical steps include cleaning and pretreating the component, applying primer, filler, intermediate layers and topcoats, then drying or curing. Depending on component geometry and production volume, application may use rollers, spraying, curtain coating or other automated methods.

UV and LED-UV coatings are particularly suitable for fast industrial processes because curing can take place immediately after application. This enables short cycle times, repeatable surfaces and immediate subsequent processing or packaging. Successful integration requires application, conveyor speed, curing and component handling to be designed as one process.

UZIN UTZ Industry develops multilayer coating systems from primer to topcoat. They stabilise industrial processes and provide lasting surface protection against abrasion, scratches, chemicals and moisture.

Repeatable layer thicknesses result from controlled coordination of material, application and line speed. Key process parameters include applied quantity, viscosity, material temperature, conveyor speed, application width and uniform coverage.

UV and LED-UV systems also require control of radiation intensity and dose, distance from the light source, exposure time and the spectral match between the coating and UV technology. Component geometry, shadowed areas and uneven surfaces can also affect complete curing.

Specific limits depend on the product and application. They should be established during process development using the actual component, defined in a mandatory process window and validated before release for series production, allowing consistent surface quality, high abrasion resistance and stable industrial coating processes. UZIN UTZ documentation confirms the focus on UV and LED-UV systems, stable processes and consistent quality, but does not provide universal settings.

Surface pretreatment depends on the material, surface condition and intended coating function. In general, the substrate must be clean, dry, sound and free from dust, grease, release agents or other residues that could impair adhesion.

Depending on the surface, wood and wood-based materials may be sanded, cleaned of dust and prepared with a suitable primer. Metals may require cleaning, degreasing and, where necessary, mechanical or chemical pretreatment. Plastics and composites must be assessed for surface energy, material compatibility and possible release agents. For already coated components, the existing layer must be checked for soundness and compatibility with the new coating.

Primers and intermediate layers then create a coordinated bond between the substrate and topcoat. Before release for series production, adhesion, material compatibility, abrasion resistance and ageing resistance should be tested on the complete assembly. UZIN UTZ therefore considers coatings as a multilayer system of primer, filler, intermediate layer and topcoat.

Visual, mechanical and measurement-based quality checks can be integrated into series production. Camera-based surface inspection can identify defects, contamination, runs, bubbles, craters or uneven coatings, for example.

Layer thickness, gloss level, colour, surface texture and curing condition can also be checked in line or through defined sampling. Material consumption, line speed, UV or LED-UV output and other process data can be recorded automatically and assigned to individual batches or components. Additional adhesion, scratch, abrasion or indentation tests are performed at defined intervals, depending on the application and safety requirements.

An industrial inspection plan should define the characteristics monitored, applicable tolerances and criteria for component approval. Documented quality control supports repeatable coatings, reduces rework and simplifies subsequent certification. UZIN UTZ Industry describes its coating systems as comprehensively tested solutions for consistent quality, load resistance and process reliability.

Repair or recoating begins with an assessment of the existing layers. Depending on the system, sound coatings can be cleaned, lightly sanded and overcoated with compatible intermediate layers or topcoats. Damaged or unsound areas must be removed locally or completely, then rebuilt.

Repair-friendly design considers future surface access, layer renewal and material compatibility during product development. This extends component life, limits rework to affected areas and avoids replacing entire components.

Recycling depends on the bond strength between coating and carrier material and compatibility with the intended recycling process. Assess coated components as complete material assemblies. Depending on the system, options include dismantling, mechanical removal, reprocessing or recovery of the combined materials. UZIN UTZ Industry considers durability, repairability and recycling during system development as part of its lifecycle approach. Its documentation supports this aim but gives no universal recycling method for all coatings and carrier materials.

Adhesive technology starts with the complete system

Many technologies, many applications. The right solution depends on the interplay of materials, design, manufacturing and subsequent use.

We test materials and assemblies for long-term loads, compatibility and ageing resistance, then develop a 

solution tailored to your industrial application, manufacturing conditions and system requirements.

We advise manufacturers and system partners on processes and applications, from material analysis and process integration to series production approval. 

Together, we engineer tailored assemblies for more efficient industrial processes today and changing requirements tomorrow.

Let’s explore what your 
system could do next.

Ready to optimise your process and improve your system? 
Tell us about your application.

Develop your system solution now